LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Land Rover >> 2012 >> LR4 HSE Lux >> Repair and Diagnosis >> Accessories & Equipment >> Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.) >> Wiring Harnesses >> Wiring Harnesses >> Removal And Installation >> Frame Wiring Harness (Vehicles Built From: 01/2007) >> Installation

Frame Wiring Harness (Vehicles Built From: 01/2007): Installation

  1. Check the old frame wiring harness against the new frame wiring harness to make sure that they are the same.
    2. NOTE: Make sure the wiring harness is routed correctly.
  2. With assistance, install the frame wiring harness.
    • Route all of the frame wiring harness electrical connectors and clips into position.
  3. Secure the brake pipes.
  4. Secure the exhaust heat shield.
    5. WARNING: Secure the component to the transmission jack.
    CAUTION: Note the rear bolt is fitted with 2 washers.
  5. Using a transmission jack, lower the fuel tank.
    • Remove the 4 bolts.
  6. Connect the fuel pump module electrical connector.
  7. RH side: Secure the frame wiring harness to the fuel tank.
  8. Rear of fuel tank: Secure the frame wiring harness to the top of the frame crossmember.
    9. CAUTION: Note the rear bolt is fitted with 2 washers.
  9. Install the fuel tank.
    • Tighten the bolts to 45 Nm (33 lb.ft).
  10. Secure the parking brake emergency release cable.
    • Secure in the 4 clips.
  11. Install the fuel tank heat shield.
    • Tighten the bolts to 6 Nm (4 lb.ft).
    • Tighten the nuts to 3 Nm (2 lb.ft).
  12. Install the transmission under shield.
    • Tighten the bolts to 10 Nm (7 lb.ft).
  13. RH side: Secure the frame wiring harness to the frame.
  14. Secure the frame wiring harness to the RH parking brake cable.
  15. Secure the RH parking brake cable bracket.
    • Install the inner section of the parking brake cable bracket.
  16. Secure the RH parking brake cable.
    • Secure the clip.
    • Tighten the new bolts to 22 Nm (16 lb.ft).
  17. Connect the electronic parking brake actuator electrical connector.
    • Secure the clip.
  18. RH side rear: Connect the low brake pad warning lamp electrical connector.
    • Secure the 2 clips.
  19. RH side rear: Connect the ABS sensor electrical connector.
    • Secure the 2 clips.
  20. Spare wheel aperture: Secure the frame wiring harness.
    • Secure the 5 clips.
  21. Secure the parking brake actuator mount bracket.
    • Tighten the bolts to 22 Nm (16 lb.ft).
  22. Connect the LH rear ABS sensor.
    • Secure the clip.
  23. LH side rear: Connect the 2 electrical connectors to the frame wiring harness.
    • Secure the electrical connectors.
  24. Reposition the rear valve block electrical connector.
  25. Reposition the RH side rear height sensor electrical connector.
  26. LH side rear: Connect the air suspension valve block electrical connector.
    • Secure the clip.
  27. Connect the electrical connector to the rear LH height sensor.
    • Secure the clip.
  28. Secure the valve block to its mounting.
  29. LH side: Secure the frame wiring harness.
    • Tighten the bolt to 22 Nm (16 lb.ft).
  30. Secure the parking brake emergency release cable.
    • Secure the clips.
  31. Secure the frame wiring harness to the LH parking brake cable.
  32. Attach both stabilizer bar links.
    • Tighten the nuts to 115 Nm (85 lb.ft).
  33. Secure the stabilizer bar.
    • Tighten the bolts to 62 Nm (46 lb.ft).
  34. Install the rear wheels and tires.
  35. Secure the air suspension compressor valve block.
  36. Connect the electrical connectors to the air suspension solenoid.
  37. Install the air suspension silencer. Refer to: Air Suspension Muffler information.
  38. LH side: Secure the air suspension line to the frame wiring harness.
  39. LH side: Secure the frame wiring harness to the frame.
    • Secure the 6 clips.
  40. Install the air suspension reservoir. Refer to: Air Suspension Reservoir information.
  41. Connect the ground cable to the wheel arch earth stud.
    • Tighten the nut to 25 Nm (18 lb.ft).
    • Secure the 2 clips.
  42. LH side front: Connect the height sensor electrical connector.
  43. Install the frame wiring harness carrier.
    • Install new tie straps.
    • Secure to the clips.
  44. LH side front: Secure the 2 windshield washer jet hoses.
  45. Reposition the frame wiring harness through the inner fender.
  46. LH side behind headlamp: Secure the 2 clips to the inner wing.
  47. LH side behind the front panel: Connect the 2 electrical connectors to the frame wiring harness.
  48. LH side behind the front headlamp: Connect the frame wiring harness electrical connector.
  49. Install the windshield washer reservoir filler neck.
  50. Install the LH front wheel arch liner. Refer to: Fender Splash Shield information.
  51. Connect the battery ground cable. Refer to: Specifications information.
scientia non olet · About LEMON Manuals