DTC: Transmission Control Module (TCM) - Siemens: DTC's
| DTC | Description | Possible Causes | Action |
|---|---|---|---|
| P0121-86 | Throttle/Pedal Position Sensor A Circuit Range/Performance - Signal invalid |
|
Check for Engine Control Module DTCs |
| P0219-86 | Engine Overspeed Condition - Signal invalid |
|
Check for Engine Control Module DTCs |
| P0500-81 | Vehicle Speed Sensor A - Invalid serial data received |
|
Check for ABS related DTCs |
| P0501-81 | Vehicle Speed Sensor A Range/Performance - Invalid serial data received |
|
Check for ABS related DTCs |
| P0561-1C | System Voltage Unstable - Circuit voltage out of range |
|
Check the battery and charging system. Refer to the relevant workshop manual section |
| P0562-21 | System Voltage Low - Signal amplitude < minimum |
|
Check the battery condition and state of charge. Check the Transmission Control Module connector and power supply circuits. Refer to the electrical circuit diagrams |
| P0563-22 | System Voltage High - Signal amplitude > maximum |
|
Check the battery condition and state of charge. Check the Transmission Control Module connector and power supply circuits. Refer to the electrical circuit diagrams |
| P0601-41 | Internal Control Module Memory Check Sum Error- General checksum failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0604-92 | Internal Control Module Random Access Memory (RAM) Error - Performance or incorrect operation |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0613-06 | TCM Processor - Algorithm Based Failures |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0613-47 | TCM Processor - Watchdog/safety microcontroller failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0613-68 | TCM Processor - Event information |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P061B-00 | Internal Control Module Torque Calculation Performance - No sub type information |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P061B-64 | Internal Control Module Torque Calculation Performance# - Signal plausibility failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P062F-04 | Internal Control Module EEPROM Error - System internal failures |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0642-21 | Sensor Reference Voltage A Circuit Low - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0643-22 | Sensor Reference Voltage A Circuit High - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0657-13 | Actuator Supply Voltage A Circuit / Open - Circuit open |
|
Check for other related DTCs. Check the park lock actuator, the actuator connector and wiring. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and test the shift lever in all positions. If the problem persists, renew the Transmission Control Module Refer to the warranty policies and procedures before renewing the transmission |
| P0658-11 | Actuator Supply Voltage A Circuit Low - Circuit short to ground |
|
Check for other related DTCs. Check the park lock actuator, the actuator connector and wiring. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and test the shift lever in all positions. If the problem persists, renew the Transmission Control Module Refer to the warranty policies and procedures before renewing the transmission |
| P0659-12 | Actuator Supply Voltage A Circuit High - Circuit short to battery |
|
Check for other related DTCs. Check the park lock actuator, the actuator connector and wiring. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and test the shift lever in all positions. If the problem persists, renew the Transmission Control Module Refer to the warranty policies and procedures before renewing the transmission |
| P0667-01 | PCM / ECM / TCM Internal Temperature Sensor Range/Performance - General electrical failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module Consider environmental conditions before condemning the module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0667-04 | PCM / ECM / TCM Internal Temperature Sensor Range/Performance - System internal failures |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module Consider environmental conditions before condemning the module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0667-49 | PCM / ECM / TCM Internal Temperature Sensor A Circuit Low - Internal electronic failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module Consider environmental conditions before condemning the module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0700-02 | Transmission Control System (MIL Request) - General signal failure |
|
Check for other DTCs and rectify those first. Clear the DTCs and road test the vehicle. If further DTCs are logged, investigate according to the individual faults logged |
| P0700-22 | Transmission Control System (MIL Request) - Signal amplitude > maximum |
|
Check for other DTCs and rectify those first. Clear the DTCs and road test the vehicle. If further DTCs are logged, investigate according to the individual faults logged |
| P0700-75 | Transmission Control System (MIL Request) - Emergency position not reachable |
|
Check for other DTCs and rectify those first. Clear the DTCs and road test the vehicle. If further DTCs are logged, investigate according to the individual faults logged |
| P0710-15 | Transmission Fluid Temperature Sensor A Circuit - Circuit short to battery or open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0711-22 | Transmission Fluid Temperature Sensor A Circuit Range/Performance - Signal amplitude > maximum |
|
Allow the transmission to cool, clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0712-11 | Transmission Fluid Temperature Sensor A Circuit Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0716-14 | Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Circuit short to ground or open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0716-21 | Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0716-22 | Turbine/Input Shaft Speed Sensor A Circuit Range/Performance - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0717-12 | Turbine/Input Shaft Speed Sensor A Circuit No Signal - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0720-12 | Output Shaft Speed Sensor Circuit - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0720-14 | Output Shaft Speed Sensor Circuit - Circuit short to ground or open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0721-22 | Output Shaft Speed Sensor Circuit Range/Performance - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0721-27 | Output Shaft Speed Sensor Circuit Range/Performance - Signal rate of change above threshold |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0721-64 | Output Shaft Speed Sensor Circuit Range/Performance - Signal plausibility failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0729-07 | Gear 6 Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0731-07 | Gear 1 Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0732-07 | Gear 2 Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0733-07 | Gear 3 Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0734-07 | Gear 4 Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0735-07 | Gear 5 Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0736-07 | Reverse Incorrect Ratio - Mechanical Failures |
|
Renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0740-13 | Torque Converter Clutch Solenoid Circuit / Open - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0741-07 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off - Mechanical Failures |
|
Renew the torque convertor. If the transmission oil condition is very poor/dirty, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0781-07 | 1 - 2 Shift - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0781-77 | 1 - 2 Shift - Commanded position not reachable |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0782-07 | 2 - 3 Shift - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0782-77 | 2 - 3 Shift - Commanded position not reachable |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0783-07 | 3 - 4 Shift - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0783-77 | 3 - 4 Shift - Commanded position not reachable |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0784-07 | 4 - 5 Shift - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0784-77 | 4 - 5 Shift - Commanded position not reachable |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0798-1E | Pressure Control Solenoid C Electrical - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0798-21 | Pressure Control Solenoid C Electrical - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0798-22 | Pressure Control Solenoid C Electrical - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0815-33 | Upshift Switch Circuit - Signal low time > maximum |
|
Refer to the electrical circuit diagrams and check the circuit between the command upshift switch and the Transmission Control Module Check the switch operation of the Transmission Shift Selector |
| P0816-33 | Downshift Switch Circuit - Signal low time > maximum |
|
Check the steering wheel gear change switches and the manual/sport gate switch operation at the gear shift lever. Refer to the electrical circuit diagrams and check the switch circuit |
| P081C-62 | Park Input Circuit - Signal compare failure |
|
Check locking mechanism operation in Park and the Park confirmation switch operation. Refer to the electrical circuit diagrams and check the switch circuit |
| P081C-64 | Park Input Circuit - Signal plausibility failure |
|
Check locking mechanism operation in Park and the Park confirmation switch operation. Refer to the electrical circuit diagrams and check the switch circuit |
| P0826-62 | Up and Down Switch Circuit - Signal compare failure |
|
Refer to the electrical circuit diagrams and check the circuit between the command shift switch and the Transmission Control Module Check the switch operation of the Transmission Shift Selector |
| P0829-07 | 5-6 Shift - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0829-77 | 5-6 Shift - Commanded position not reachable |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and road test the vehicle. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P0850-29 | Park / Neutral Switch Input Circuit - Signal invalid |
|
Refer to the electrical circuit diagrams and check the park/neutral switch circuit between the central electronics module, the Engine Control Module and Transmission Control Module Clear the DTC and check that the engine starts in park and neutral and not in any other selected position. If the fault persists, renew the renew the Transmission Control Module |
| P0915-01 | Gear Shift Position Circuit Range/Performance - General electrical failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0915-64 | Gear Shift Position Circuit Range/Performance - Signal plausibility failure |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0930-00 | Gear Shift Lock Solenoid/Actuator Circuit A Low - No sub type information |
|
Check for other related DTCs. Check the shift lock actuator, the connectors and wiring. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and test the shift lever in all positions. If the problem persists, renew the Transmission Control Module Refer to the warranty policies and procedures before renewing the transmission |
| P0931-00 | Gear Shift Lock Solenoid/Actuator Circuit A High - No sub type information |
|
Check for other related DTCs. Check the shift lock actuator, the connectors and wiring. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and test the shift lever in all positions. If the problem persists, renew the Transmission Control Module Refer to the warranty policies and procedures before renewing the transmission |
| P0938-29 | Hydraulic Oil Temperature Sensor Range/Performance - Signal invalid |
|
Allow the transmission to cool, clear the DTC and road test the vehicle. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0963-12 | Pressure Control Solenoid A Control Circuit High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0963-13 | Pressure Control Solenoid A Control Circuit High - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0964-13 | Pressure Control Solenoid B Control Circuit / Open - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0966-11 | Pressure Control Solenoid B Control Circuit Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0966-14 | Pressure Control Solenoid B Control Circuit Low - Circuit short to ground or open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0966-1E | Pressure Control Solenoid B Control Circuit Low - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0966-21 | Pressure Control Solenoid B Control Circuit Low - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0967-12 | Pressure Control Solenoid B Control Circuit High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0967-22 | Pressure Control Solenoid B Control Circuit High - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0968-13 | Pressure Control Solenoid C Control Circuit / Open - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0970-11 | Pressure Control Solenoid C Control Circuit Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0970-14 | Pressure Control Solenoid C Control Circuit Low - Circuit short to ground or open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0971-12 | Pressure Control Solenoid C Control Circuit High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0972-21 | Shift Solenoid A Control Circuit Range/Performance - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0972-22 | Shift Solenoid A Control Circuit Range/Performance - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0973-11 | Shift Solenoid A Control Circuit Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0973-14 | Shift Solenoid A Control Circuit Low - Circuit short to ground or open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P0973-1E | Shift Solenoid A Control Circuit Low - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P1706-9A | High Vehicle Speed Observed in Park - component or system operating conditions |
|
NOTE:
Park mechanism damage associated with this DTC may not be covered under the manufacturers warranty. Check parking pawl/park mechanism for correct operation. Clear DTC and retest |
| P2700-07 | Transmission Friction Element A Apply Time Range/Performance - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P2701-07 | Transmission Friction Element B Apply Time Range/Performance - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P2702-07 | Transmission Friction Element C Apply Time Range/Performance - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P2703-07 | Transmission Friction Element D Apply Time Range/Performance - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P2704-07 | Transmission Friction Element E Apply Time Range/Performance - Mechanical Failures |
|
Check the fluid level and condition. Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the transmission. Refer to the warranty policies and procedures before renewing the transmission |
| P2716-1E | Pressure Control Solenoid D Electrical - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2716-21 | Pressure Control Solenoid D Electrical - Signal Amplitude < Minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2716-22 | Pressure Control Solenoid D Electrical - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2718-13 | Pressure Control Solenoid D Control Circuit / Open - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2720-11 | Pressure Control Solenoid D Control Circuit Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2720-14 | Pressure Control Solenoid D Control Circuit Low - Circuit short to ground or open circuit |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2721-12 | Pressure Control Solenoid D Control Circuit High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2725-1E | Pressure Control Solenoid E Electrical - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2725-21 | Pressure Control Solenoid E Electrical - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2725-22 | Pressure Control Solenoid E Electrical - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2727-13 | Pressure Control Solenoid E Control Circuit / Open - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2729-11 | Pressure Control Solenoid E Control Circuit Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2729-14 | Pressure Control Solenoid E Control Circuit Low - Circuit short to ground or open circuit |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2730-12 | Pressure Control Solenoid E Control Circuit High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2734-1E | Pressure Control Solenoid F Electrical - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2734-21 | Pressure Control Solenoid F Electrical - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2734-22 | Pressure Control Solenoid F Electrical - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2736-13 | Pressure Control Solenoid F Control Circuit / Open - Circuit open |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2738-11 | Pressure Control Solenoid F Control Low - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2738-14 | Pressure Control Solenoid F Control Low - Circuit short to ground or open circuit |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2739-12 | Pressure Control Solenoid F Control High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2763-12 | Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Circuit short to battery |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2763-22 | Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Signal amplitude > maximum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2764-11 | Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Circuit short to ground |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2764-14 | Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Circuit short to ground or open circuit |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2764-1E | Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Circuit resistance out of range |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| P2764-21 | Torque Converter Clutch Pressure Control Solenoid Control Circuit High - Signal amplitude < minimum |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |
| U0001-88 | High Speed CAN Communication CAN Bus - Bus off | Bus off | Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network |
| U0100-00 | Lost Communication With ECM/PCM "A" - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0102-00 | Lost Communication with Transfer Case Control Module - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0121-00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0126-00 | Lost Communication With Steering Angle Sensor Module - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0128-00 | Lost Communication With Park Brake Control Module - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0138-00 | Lost Communication with All Terrain Control Module - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0140-00 | Lost Communication With Body Control Module - No sub type information |
|
Check for other CAN Bus off codes. Examine E-box for water ingress, moisture or loose plugs. Refer to the electrical circuit diagrams and check the module connector and power/ground circuits. Refer to network communication section of the workshop manual. Using the manufacturers approved diagnostic system, complete a CAN integrity test |
| U0300-00 | Internal Control Module Software Incompatibility - No sub type information |
|
Check for other modules reporting CAN Bus off or lost communication faults. If other modules report problems, check the software version in the Central Junction Box (GEM) using the manufacturers approved diagnostic system. If no other modules report problems, check the software version in the Transmission Control Module Update as necessary |
| U0401-00 | Invalid Data Received from ECM/PCM A - No sub type information |
|
Check for other module related DTCs. Refer to the relevant section in the workshop manual. Check the control module for correct software version using the manufacturers approved diagnostic system |
| U0401-64 | Invalid Data Received from ECM/PCM A - Signal plausibility failure |
|
Check for other module related DTCs. Refer to the relevant section in the workshop manual. Check the control module for correct software version using the manufacturers approved diagnostic system |
| U0401-68 | Invalid Data Received from ECM/PCM A - Event information |
|
Check for other module related DTCs. Refer to the relevant section in the workshop manual. Check the control module for correct software version using the manufacturers approved diagnostic system |
| U0415-64 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module - Signal plausibility failure |
|
Check for other module related DTCs. Refer to the relevant section in the workshop manual. Check the control module for correct software version using the manufacturers approved diagnostic system |
| U0415-68 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module - Event information |
|
Check for other module related DTCs. Refer to the relevant section in the workshop manual. Check the control module for correct software version using the manufacturers approved diagnostic system |
| U0422-68 | Invalid Data Received From Central Electronics Module - Event information |
|
Check the operation of the command shift switch. Check the electrical connections to the switch. Refer to the electrical circuit diagrams and check the circuit between the command shift switch and the Transmission Control Module. Check the power/ground circuits and the Central Junction Box connector. Refer to the lost communication statement in the network communication section of the workshop manual |
| U2101-00 | Control Module Configuration Incompatible - No sub type information |
|
Check that the vehicle configuration is correctly set in the car configuration file using the manufacturer's approved diagnostic software. Check and update the Transmission Control Module software version if necessary |
| U3000-4B | Control Module - Over temperature |
|
Check the Transmission Control Module connector and the power/ground circuits to the module. Refer to the electrical circuit diagrams and check the transmission cooling circuit. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module Consider environmental conditions before condemning the module. Refer to the warranty policy and procedures manual if a module is suspect |
| U3001-94 | Control Module Improper Shutdown - Unexpected operation |
|
DTC for information only. Clear the DTC and retest. If the problem persists, renew the Transmission Control Module. Refer to the warranty policy and procedures manual if a module is suspect |